Fix S2 compiling

src/ESP32-HUB75-MatrixPanel-I2S-DMA.h

@@ -844,7 +844,7 @@ private:
   frameStruct frame_buffer[2];
   frameStruct *fb; // What framebuffer we are writing pixel changes to? (pointer to either frame_buffer[0] or frame_buffer[1] basically ) used within updateMatrixDMABuffer(...)
 
-  int back_buffer_id = 0;      // If using double buffer, which one is NOT active (ie. being displayed) to write too?
+  volatile int back_buffer_id = 0;      // If using double buffer, which one is NOT active (ie. being displayed) to write too?
   int brightness = 128;        // If you get ghosting... reduce brightness level. ((60/64)*255) seems to be the limit before ghosting on a 64 pixel wide physical panel for some panels.
   int lsbMsbTransitionBit = 0; // For colour depth calculations
 

src/platforms/esp32/esp32_i2s_parallel_dma.cpp

@@ -36,19 +36,23 @@ Modified heavily for the ESP32 HUB75 DMA library by:
 #include <soc/rtc.h>
 
 
-volatile bool previousBufferFree = true;
+	volatile bool previousBufferFree = true;
 
-// Todo: handle IS20? (this is hard coded for I2S1 only)
+	static void IRAM_ATTR i2s_isr(void* arg) {
-static void IRAM_ATTR i2s_isr(void* arg) {
+
-    REG_WRITE(I2S_INT_CLR_REG(1), (REG_READ(I2S_INT_RAW_REG(1)) & 0xffffffc0) | 0x3f);
+		// From original Sprite_TM Code
+		//REG_WRITE(I2S_INT_CLR_REG(1), (REG_READ(I2S_INT_RAW_REG(1)) & 0xffffffc0) | 0x3f);
+		
+		// Clear flag so we can get retriggered
+		SET_PERI_REG_BITS(I2S_INT_CLR_REG(ESP32_I2S_DEVICE), I2S_OUT_EOF_INT_CLR_V, 1, I2S_OUT_EOF_INT_CLR_S);                      
 		
 		// at this point, the previously active buffer is free, go ahead and write to it
 		previousBufferFree = true;
-}
+	}
 
-bool DRAM_ATTR i2s_parallel_is_previous_buffer_free() {
+	bool DRAM_ATTR i2s_parallel_is_previous_buffer_free() {
 		return previousBufferFree;
-}
+	}
 
 
 	// Static
@@ -370,26 +374,22 @@ bool DRAM_ATTR i2s_parallel_is_previous_buffer_free() {
     dev->timing.val = 0;
 
 
-    /* If we have double buffering, then allocate an interrupt service routine function
+    // If we have double buffering, then allocate an interrupt service routine function
-     * that can be used for I2S0/I2S1 created interrupts.
+    // that can be used for I2S0/I2S1 created interrupts.
-     */
 
-     // setup I2S Interrupt
+    // Setup I2S Interrupt
-    SET_PERI_REG_BITS(I2S_INT_ENA_REG(1), I2S_OUT_EOF_INT_ENA_V, 1, I2S_OUT_EOF_INT_ENA_S);
+    SET_PERI_REG_BITS(I2S_INT_ENA_REG(ESP32_I2S_DEVICE), I2S_OUT_EOF_INT_ENA_V, 1, I2S_OUT_EOF_INT_ENA_S);
-    // allocate a level 1 intterupt: lowest priority, as ISR isn't urgent and may take a long time to complete
+
-    //esp_intr_alloc(ETS_I2S1_INTR_SOURCE, (int)(ESP_INTR_FLAG_IRAM | ESP_INTR_FLAG_LEVEL1), i2s_isr, NULL, NULL);
+    // Allocate a level 1 intterupt: lowest priority, as ISR isn't urgent and may take a long time to complete
     esp_intr_alloc(irq_source, (int)(ESP_INTR_FLAG_IRAM | ESP_INTR_FLAG_LEVEL1), i2s_isr, NULL, NULL);
 
  
-
-      
   #if defined (CONFIG_IDF_TARGET_ESP32S2)
       ESP_LOGD("ESP32-S2", "init() GPIO and clock configuration set for ESP32-S2");    
   #else
       ESP_LOGD("ESP32-ORIG", "init() GPIO and clock configuration set for ESP32");    
   #endif
 
-
       return true;
   }
 

src/platforms/esp32/esp32_i2s_parallel_dma.hpp

@@ -49,12 +49,16 @@ Contributors:
 
 #define DMA_MAX (4096-4)
 
-// DO NOT CHANGE
-#define ESP32_I2S_DEVICE I2S_NUM_1	
-
 // The type used for this SoC
 #define HUB75_DMA_DESCRIPTOR_T lldesc_t
 
+
+#if defined (CONFIG_IDF_TARGET_ESP32S2)   
+#define ESP32_I2S_DEVICE I2S_NUM_0	
+#else
+#define ESP32_I2S_DEVICE I2S_NUM_1	
+#endif	
+
 //----------------------------------------------------------------------------
 
 void IRAM_ATTR irq_hndlr(void* arg);