ESP32-HUB75-MatrixPanel-DMA/esp32_i2s_parallel_dma_cxxx.txt
mrfaptastic dd05550cc5 Remove ESP32C3 experimental stuff.
ESP32-C3 doesn't actually support 'lcd mode' aka. parallel DMA, so it'll never be of use with this library and a HUB75 panel.
2021-09-29 23:20:16 +01:00

313 lines
No EOL
9.1 KiB
Text

/*
* ESP32_I2S_PARALLEL_DMA (Version 3)
*
* Author: Mrfaptastic @ https://github.com/mrfaptastic/
*
* Description: Multi-ESP32 product DMA setup functions for ESP32 C3/H2 RISC-V chips
*
* ESP32C series doesn't support LCD mode / parallel DMA!
*
*/
// Header
#include "esp32_i2s_parallel_dma.h"
#if defined(ESP32_CXXX)
#include <esp_err.h>
// Turn on and off a periphal
#include <driver/periph_ctrl.h>
// GPIO
#include <soc/gpio_periph.h>
#include <hal/gpio_types.h>
#include <driver/gpio.h>
#include <driver/periph_ctrl.h>
#include <rom/gpio.h>
#include <soc/gpio_sig_map.h>
// DMA Linked List Struct
#include <soc/lldesc.h>
#include <soc/io_mux_reg.h>
// I2S
#include <soc/i2s_struct.h>
#include <soc/i2s_reg.h>
// GDMA
#include <soc/gdma_channel.h>
#include <soc/gdma_periph.h>
#include <soc/gdma_reg.h>
#include <soc/gdma_struct.h>
// For I2S state management.
static i2s_parallel_state_t *i2s_state = NULL;
// ESP32-S2,S3,C3 only has IS20
// Original ESP32 has two I2S's, but we'll stick with the lowest common denominator.
static i2s_dev_t* I2S = &I2S0; // Device to use for this library, change if you want.
callback shiftCompleteCallback;
void setShiftCompleteCallback(callback f) {
shiftCompleteCallback = f;
}
volatile bool previousBufferFree = true;
static void IRAM_ATTR gdma_irq_handler(void* arg) { // if we use I2S1 (default)
GDMA.intr[0].clr.out_eof = 1;
// at this point, the previously active buffer is free, go ahead and write to it
// previousBufferFree = true;
// if(shiftCompleteCallback) // we've defined a callback function ?
// shiftCompleteCallback();
// at this point, the previously active buffer is free, go ahead and write to it
previousBufferFree = true;
if(shiftCompleteCallback) // we've defined a callback function ?
shiftCompleteCallback();
} // end irq_hndlr
// For peripheral setup and configuration
static inline int get_bus_width(i2s_parallel_cfg_bits_t width) {
switch(width) {
case I2S_PARALLEL_WIDTH_8:
return 8;
case I2S_PARALLEL_WIDTH_16:
return 16;
case I2S_PARALLEL_WIDTH_24:
return 24;
default:
return -ESP_ERR_INVALID_ARG;
}
}
static void gpio_setup_out(int gpio, int sig) {
if(gpio < 0) {
return;
}
// Configure GPIO
// https://github.com/espressif/esp-idf/blob/d5f58ab13551cd883e8d8478ba367b6e4543ffec/examples/peripherals/gpio/generic_gpio/main/gpio_example_main.c
gpio_config_t io_conf = {};
io_conf.intr_type = GPIO_INTR_DISABLE;
io_conf.mode = GPIO_MODE_DEF_OUTPUT;
io_conf.pin_bit_mask = (1ULL << gpio);
io_conf.pull_down_en = 1;
io_conf.pull_up_en = 0;
gpio_config(&io_conf);
// Set IOMUX to GPIO
//gpio_iomux_out(gpio, sig, false); // ?? is sig right?
gpio_matrix_out(gpio, sig, false, false);
// Drive Strength to MAX
gpio_set_drive_capability((gpio_num_t)gpio, (gpio_drive_cap_t)3);
}
// DMA Linked List
// Size must be less than DMA_MAX - need to handle breaking long transfer into two descriptors before call
// DMA_MAX by the way is the maximum data packet size you can hold in one chunk
void link_dma_desc(volatile lldesc_t *dmadesc, volatile lldesc_t *prevdmadesc, void *memory, size_t size)
{
if(size > DMA_MAX) size = DMA_MAX;
dmadesc->size = size;
dmadesc->length = size;
dmadesc->buf = memory;
dmadesc->eof = 0;
dmadesc->sosf = 0;
dmadesc->owner = 1;
dmadesc->qe.stqe_next = 0; // will need to set this elsewhere
dmadesc->offset = 0;
// link previous to current
if(prevdmadesc)
prevdmadesc->qe.stqe_next = (lldesc_t*)dmadesc;
}
esp_err_t i2s_parallel_driver_install(i2s_port_t port, i2s_parallel_config_t* cfg) {
port = I2S_NUM_0; /// override.
if(port < I2S_NUM_0 || port >= I2S_NUM_MAX) {
return ESP_ERR_INVALID_ARG;
}
if(cfg->sample_width < I2S_PARALLEL_WIDTH_8 || cfg->sample_width >= I2S_PARALLEL_WIDTH_MAX) {
return ESP_ERR_INVALID_ARG;
}
if(cfg->sample_rate > I2S_PARALLEL_CLOCK_HZ || cfg->sample_rate < 1) {
return ESP_ERR_INVALID_ARG;
}
uint32_t clk_div_main = I2S_PARALLEL_CLOCK_HZ / cfg->sample_rate / i2s_parallel_get_memory_width(port, cfg->sample_width);
if(clk_div_main < 2 || clk_div_main > 0xFF) {
return ESP_ERR_INVALID_ARG;
}
// Setup GPIOs
int bus_width = get_bus_width(cfg->sample_width);
i2s_dev_t *i2s_dev = I2S; // There's only one I2S device on C3....
//Figure out which signal numbers to use for routing
//printf("Setting up parallel I2S bus at I2S%d\n", i2snum(dev));
int sig_data_base = I2SO_SD_OUT_IDX;
int sig_clk = I2SO_WS_OUT_IDX;
//Route the signals
for (int x=0; x < bus_width; x++) {
gpio_setup_out(cfg->gpio_bus[x], sig_data_base+x);
}
//ToDo: Clk/WS may need inversion?
gpio_setup_out(cfg->gpio_clk, sig_clk);
// Power on I2S1 (or 0)
periph_module_enable(PERIPH_I2S1_MODULE);
// Now it's apparently I2S0 !?
//i2s_dev_t *i2s_dev = &I2S0;
// Reset RX (not that we use it)
i2s_dev->rx_conf.val = 0;
i2s_dev->rx_conf.rx_reset=1; i2s_dev->rx_conf.rx_reset=0;
i2s_dev->rx_conf.rx_fifo_reset=1; i2s_dev->rx_conf.rx_fifo_reset=0;
// Reset TX (what we care about)
i2s_dev->tx_conf.val = 0;
i2s_dev->tx_conf.tx_reset=1; i2s_dev->tx_conf.tx_reset=0;
i2s_dev->tx_conf.tx_fifo_reset=1; i2s_dev->tx_conf.tx_fifo_reset=0;
i2s_dev->tx_conf.tx_chan_equal=1;
// Device setup
i2s_dev->tx_conf1.val = 0;
i2s_dev->tx_conf1.tx_bits_mod=16;//cfg->bits;
i2s_dev->rx_conf1.val = 0;
i2s_dev->rx_conf1.rx_bits_mod=16; //cfg->bits;
i2s_dev->tx_conf1.tx_bck_div_num=2;
i2s_dev->rx_conf1.rx_bck_div_num=2;
i2s_dev->tx_clkm_conf.val=0;
i2s_dev->tx_clkm_conf.tx_clk_sel=2; // 160mhz
// clock speed
i2s_dev->tx_clkm_conf.tx_clkm_div_num=160/16; // 10Mhz
//i2s_dev->tx_clkm_div_conf.val = 0; //
i2s_dev->tx_clkm_div_conf.tx_clkm_div_x = 0; // > ?
i2s_dev->tx_clkm_div_conf.tx_clkm_div_y = 0; //
i2s_dev->tx_clkm_div_conf.tx_clkm_div_yn1 = 0;
i2s_dev->tx_clkm_div_conf.tx_clkm_div_z = 0;
i2s_dev->tx_clkm_conf.tx_clk_active=1; // Start
//Allocate DMA descriptors
i2s_state = malloc(sizeof(i2s_parallel_state_t));
assert(i2s_state != NULL);
i2s_parallel_state_t *st= i2s_state;
st->desccount_a = cfg->desccount_a;
st->desccount_b = cfg->desccount_b;
st->dmadesc_a = cfg->lldesc_a;
st->dmadesc_b = cfg->lldesc_b;
// setup I2S Interrupt
// SET_PERI_REG_BITS(I2S_INT_ENA_REG(1), I2S_OUT_EOF_INT_ENA_V, 1, I2S_OUT_EOF_INT_ENA_S);
// allocate a level 1 intterupt: lowest priority, as ISR isn't urgent and may take a long time to complete
esp_intr_alloc(ETS_I2S1_INTR_SOURCE, (int)(ESP_INTR_FLAG_IRAM | ESP_INTR_FLAG_LEVEL1), gdma_irq_handler, NULL, NULL);
GDMA.intr[0].ena.out_eof = 1; //?
// Reset GDMA device
GDMA.channel[0].out.out_conf0.out_rst = 1; // REG_SET_BIT(DMA_OUT_CONF0_CH0_REG, DMA_OUT_RST_CH0);
GDMA.channel[0].out.out_conf0.out_rst = 0; // REG_CLR_BIT(DMA_OUT_CONF0_CH0_REG, DMA_OUT_RST_CH0);
// GDMA.channel[0].out.out_conf0.out_eof_mode = 1; ?
GDMA.misc_conf.ahbm_rst_inter = 1;
GDMA.misc_conf.ahbm_rst_inter = 0;
// Setup interrupt
// Setup outlink
GDMA.channel[0].out.out_link.addr = ((uint32_t)(&st->dmadesc_a[0]));// Set a vlaue here
GDMA.channel[0].out.out_peri_sel.sel = SOC_GDMA_TRIG_PERIPH_I2S0; // 3 = I2S0
GDMA.channel[0].out.out_conf0.out_data_burst_en = 1;
GDMA.channel[0].out.out_conf0.outdscr_burst_en = 1;
GDMA.channel[0].out.out_link.start = 1;
while (!GDMA.intr->raw.out_eof) { } // check status
i2s_dev->tx_conf.tx_start = 1;
return ESP_OK;
}
esp_err_t i2s_parallel_stop_dma(i2s_port_t port) {
if(port < I2S_NUM_0 || port >= I2S_NUM_MAX) {
return ESP_ERR_INVALID_ARG;
}
// Not implemented
return ESP_OK;
}
esp_err_t i2s_parallel_send_dma(i2s_port_t port, lldesc_t* dma_descriptor) {
if(port < I2S_NUM_0 || port >= I2S_NUM_MAX) {
return ESP_ERR_INVALID_ARG;
}
// Not implemented
return ESP_OK;
}
i2s_dev_t* i2s_parallel_get_dev(i2s_port_t port) {
if(port < I2S_NUM_0 || port >= I2S_NUM_MAX) {
return NULL;
}
return I2S; // HARCODE THIS TO RETURN &I2S0
}
// Double buffering flipping
// Flip to a buffer: 0 for bufa, 1 for bufb
void i2s_parallel_flip_to_buffer(i2s_port_t port, int buffer_id) {
if (i2s_state == NULL) {
return; // :-()
}
lldesc_t *active_dma_chain;
if (buffer_id == 0) {
active_dma_chain=(lldesc_t*)&i2s_state->dmadesc_a[0];
} else {
active_dma_chain=(lldesc_t*)&i2s_state->dmadesc_b[0];
}
// setup linked list to refresh from new buffer (continuously) when the end of the current list has been reached
i2s_state->dmadesc_a[i2s_state->desccount_a-1].qe.stqe_next = active_dma_chain;
i2s_state->dmadesc_b[i2s_state->desccount_b-1].qe.stqe_next = active_dma_chain;
// we're still shifting out the buffer, so it shouldn't be written to yet.
previousBufferFree = false;
}
bool i2s_parallel_is_previous_buffer_free() {
return previousBufferFree;
}
// End ESP32 original / S2, S3 check
#endif