70 lines
3.7 KiB
Arduino
70 lines
3.7 KiB
Arduino
|
/*
|
||
|
|
Controlling a servo position using a potentiometer (variable resistor)
|
||
|
|
by Michal Rinott <http://people.interaction-ivrea.it/m.rinott>
|
||
|
|
|
||
|
|
modified on 8 Nov 2013
|
||
|
|
by Scott Fitzgerald
|
||
|
|
|
||
|
|
modified for the ESP32 on March 2017
|
||
|
|
by John Bennett
|
||
|
|
|
||
|
|
see http://www.arduino.cc/en/Tutorial/Knob for a description of the original code
|
||
|
|
|
||
|
|
* Different servos require different pulse widths to vary servo angle, but the range is
|
||
|
|
* an approximately 500-2500 microsecond pulse every 20ms (50Hz). In general, hobbyist servos
|
||
|
|
* sweep 180 degrees, so the lowest number in the published range for a particular servo
|
||
|
|
* represents an angle of 0 degrees, the middle of the range represents 90 degrees, and the top
|
||
|
|
* of the range represents 180 degrees. So for example, if the range is 1000us to 2000us,
|
||
|
|
* 1000us would equal an angle of 0, 1500us would equal 90 degrees, and 2000us would equal 1800
|
||
|
|
* degrees.
|
||
|
|
*
|
||
|
|
* Circuit: (using an ESP32 Thing from Sparkfun)
|
||
|
|
* Servo motors have three wires: power, ground, and signal. The power wire is typically red,
|
||
|
|
* the ground wire is typically black or brown, and the signal wire is typically yellow,
|
||
|
|
* orange or white. Since the ESP32 can supply limited current at only 3.3V, and servos draw
|
||
|
|
* considerable power, we will connect servo power to the VBat pin of the ESP32 (located
|
||
|
|
* near the USB connector). THIS IS ONLY APPROPRIATE FOR SMALL SERVOS.
|
||
|
|
*
|
||
|
|
* We could also connect servo power to a separate external
|
||
|
|
* power source (as long as we connect all of the grounds (ESP32, servo, and external power).
|
||
|
|
* In this example, we just connect ESP32 ground to servo ground. The servo signal pins
|
||
|
|
* connect to any available GPIO pins on the ESP32 (in this example, we use pin 18.
|
||
|
|
*
|
||
|
|
* In this example, we assume a Tower Pro SG90 small servo connected to VBat.
|
||
|
|
* The published min and max for this servo are 500 and 2400, respectively.
|
||
|
|
* These values actually drive the servos a little past 0 and 180, so
|
||
|
|
* if you are particular, adjust the min and max values to match your needs.
|
||
|
|
*/
|
||
|
|
|
||
|
|
// Include the ESP32 Arduino Servo Library instead of the original Arduino Servo Library
|
||
|
|
#include <ESP32Servo.h>
|
||
|
|
|
||
|
|
Servo myservo; // create servo object to control a servo
|
||
|
|
|
||
|
|
// Possible PWM GPIO pins on the ESP32: 0(used by on-board button),2,4,5(used by on-board LED),12-19,21-23,25-27,32-33
|
||
|
|
int servoPin = 18; // GPIO pin used to connect the servo control (digital out)
|
||
|
|
// Possible ADC pins on the ESP32: 0,2,4,12-15,32-39; 34-39 are recommended for analog input
|
||
|
|
int potPin = 34; // GPIO pin used to connect the potentiometer (analog in)
|
||
|
|
int ADC_Max = 4096; // This is the default ADC max value on the ESP32 (12 bit ADC width);
|
||
|
|
// this width can be set (in low-level oode) from 9-12 bits, for a
|
||
|
|
// a range of max values of 512-4096
|
||
|
|
|
||
|
|
int val; // variable to read the value from the analog pin
|
||
|
|
|
||
|
|
void setup()
|
||
|
|
{
|
||
|
|
myservo.attach(servoPin, 500, 2400); // attaches the servo on pin 18 to the servo object
|
||
|
|
// using SG90 servo min/max of 500us and 2400us
|
||
|
|
// for MG995 large servo, use 1000us and 2000us,
|
||
|
|
// which are the defaults, so this line could be
|
||
|
|
// "myservo.attach(servoPin);"
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
val = analogRead(potPin); // read the value of the potentiometer (value between 0 and 1023)
|
||
|
|
val = map(val, 0, ADC_Max, 0, 180); // scale it to use it with the servo (value between 0 and 180)
|
||
|
|
myservo.write(val); // set the servo position according to the scaled value
|
||
|
|
delay(200); // wait for the servo to get there
|
||
|
|
}
|
||
|
|
|