71 lines
2.9 KiB
C++
71 lines
2.9 KiB
C++
#include <FastLED.h>
|
|
|
|
|
|
////////////////////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// RGB Calibration code
|
|
//
|
|
// Use this sketch to determine what the RGB ordering for your chipset should be. Steps for setting up to use:
|
|
|
|
// * Uncomment the line in setup that corresponds to the LED chipset that you are using. (Note that they
|
|
// all explicitly specify the RGB order as RGB)
|
|
// * Define DATA_PIN to the pin that data is connected to.
|
|
// * (Optional) if using software SPI for chipsets that are SPI based, define CLOCK_PIN to the clock pin
|
|
// * Compile/upload/run the sketch
|
|
|
|
// You should see six leds on. If the RGB ordering is correct, you should see 1 red led, 2 green
|
|
// leds, and 3 blue leds. If you see different colors, the count of each color tells you what the
|
|
// position for that color in the rgb orering should be. So, for example, if you see 1 Blue, and 2
|
|
// Red, and 3 Green leds then the rgb ordering should be BRG (Blue, Red, Green).
|
|
|
|
// You can then test this ordering by setting the RGB ordering in the addLeds line below to the new ordering
|
|
// and it should come out correctly, 1 red, 2 green, and 3 blue.
|
|
//
|
|
//////////////////////////////////////////////////
|
|
|
|
#define NUM_LEDS 6
|
|
|
|
// Data pin that led data will be written out over
|
|
#define DATA_PIN 6
|
|
// Clock pin only needed for SPI based chipsets when not using hardware SPI
|
|
//#define CLOCK_PIN 8
|
|
|
|
CRGB leds[NUM_LEDS];
|
|
|
|
void setup() {
|
|
// sanity check delay - allows reprogramming if accidently blowing power w/leds
|
|
delay(2000);
|
|
|
|
// Uncomment one of the following lines for your leds arrangement.
|
|
// FastLED.addLeds<TM1803, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<TM1804, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<TM1809, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<WS2811, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<WS2812, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<WS2812B, DATA_PIN, GRB>(leds, NUM_LEDS);
|
|
// FastLED.setBrightness(CRGB(255,255,255));
|
|
// FastLED.addLeds<GW6205, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<GW6205_400, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<UCS1903, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<UCS1903B, DATA_PIN, RGB>(leds, NUM_LEDS);
|
|
|
|
// FastLED.addLeds<WS2801, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<SM16716, RGB>(leds, NUM_LEDS);
|
|
FastLED.addLeds<LPD8806, 9, 10, RGB>(leds, NUM_LEDS);
|
|
|
|
// FastLED.addLeds<WS2801, DATA_PIN, CLOCK_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<SM16716, DATA_PIN, CLOCK_PIN, RGB>(leds, NUM_LEDS);
|
|
// FastLED.addLeds<LPD8806, DATA_PIN, CLOCK_PIN, RGB>(leds, NUM_LEDS);
|
|
}
|
|
|
|
void loop() {
|
|
leds[0] = CRGB(255,0,0);
|
|
leds[1] = CRGB(0,255,0);
|
|
leds[2] = CRGB(0,255,0);
|
|
leds[3] = CRGB(0,0,255);
|
|
leds[4] = CRGB(0,0,255);
|
|
leds[5] = CRGB(0,0,255);
|
|
FastLED.show();
|
|
delay(1000);
|
|
}
|