106 lines
3.9 KiB
C++
106 lines
3.9 KiB
C++
/*
|
|
* ESP32 Servo Example Using Arduino ESP32 Servo Library
|
|
* John K. Bennett
|
|
* March, 2017
|
|
*
|
|
* This sketch uses the Arduino ESP32 Servo Library to sweep 4 servos in sequence.
|
|
*
|
|
* Different servos require different pulse widths to vary servo angle, but the range is
|
|
* an approximately 500-2500 microsecond pulse every 20ms (50Hz). In general, hobbyist servos
|
|
* sweep 180 degrees, so the lowest number in the published range for a particular servo
|
|
* represents an angle of 0 degrees, the middle of the range represents 90 degrees, and the top
|
|
* of the range represents 180 degrees. So for example, if the range is 1000us to 2000us,
|
|
* 1000us would equal an angle of 0, 1500us would equal 90 degrees, and 2000us would equal 1800
|
|
* degrees.
|
|
*
|
|
* Circuit:
|
|
* Servo motors have three wires: power, ground, and signal. The power wire is typically red,
|
|
* the ground wire is typically black or brown, and the signal wire is typically yellow,
|
|
* orange or white. Since the ESP32 can supply limited current at only 3.3V, and servos draw
|
|
* considerable power, we will connect servo power to the VBat pin of the ESP32 (located
|
|
* near the USB connector). THIS IS ONLY APPROPRIATE FOR SMALL SERVOS.
|
|
*
|
|
* We could also connect servo power to a separate external
|
|
* power source (as long as we connect all of the grounds (ESP32, servo, and external power).
|
|
* In this example, we just connect ESP32 ground to servo ground. The servo signal pins
|
|
* connect to any available GPIO pins on the ESP32 (in this example, we use pins
|
|
* 22, 19, 23, & 18).
|
|
*
|
|
* In this example, we assume four Tower Pro SG90 small servos.
|
|
* The published min and max for this servo are 500 and 2400, respectively.
|
|
* These values actually drive the servos a little past 0 and 180, so
|
|
* if you are particular, adjust the min and max values to match your needs.
|
|
* Experimentally, 550 and 2350 are pretty close to 0 and 180.
|
|
*/
|
|
|
|
#include <ESP32Servo.h>
|
|
|
|
// create four servo objects
|
|
Servo servo1;
|
|
Servo servo2;
|
|
Servo servo3;
|
|
Servo servo4;
|
|
|
|
// Published values for SG90 servos; adjust if needed
|
|
int minUs = 500;
|
|
int maxUs = 2400;
|
|
|
|
// These are all GPIO pins on the ESP32
|
|
// Recommended pins include 2,4,12-19,21-23,25-27,32-33
|
|
int servo1Pin = 18;
|
|
int servo2Pin = 19;
|
|
int servo3Pin = 22;
|
|
int servo4Pin = 23;
|
|
|
|
int pos = 0; // position in degrees
|
|
|
|
void setup()
|
|
{
|
|
servo1.attach(servo1Pin, minUs, maxUs);
|
|
servo2.attach(servo2Pin, minUs, maxUs);
|
|
servo3.attach(servo3Pin, minUs, maxUs);
|
|
servo4.attach(servo4Pin, minUs, maxUs);
|
|
}
|
|
|
|
void loop() {
|
|
for (pos = 0; pos <= 180; pos += 1) { // sweep from 0 degrees to 180 degrees
|
|
// in steps of 1 degree
|
|
servo1.write(pos);
|
|
delay(20); // waits 20ms for the servo to reach the position
|
|
}
|
|
for (pos = 180; pos >= 0; pos -= 1) { // sweep from 180 degrees to 0 degrees
|
|
servo1.write(pos);
|
|
delay(20);
|
|
}
|
|
|
|
for (pos = 0; pos <= 180; pos += 1) { // sweep from 0 degrees to 180 degrees
|
|
// in steps of 1 degree
|
|
servo2.write(pos);
|
|
delay(20); // waits 20ms for the servo to reach the position
|
|
}
|
|
for (pos = 180; pos >= 0; pos -= 1) { // sweep from 180 degrees to 0 degrees
|
|
servo2.write(pos);
|
|
delay(20);
|
|
}
|
|
|
|
for (pos = 0; pos <= 180; pos += 1) { // sweep from 0 degrees to 180 degrees
|
|
// in steps of 1 degree
|
|
servo3.write(pos);
|
|
delay(20); // waits 20ms for the servo to reach the position
|
|
}
|
|
for (pos = 180; pos >= 0; pos -= 1) { // sweep from 180 degrees to 0 degrees
|
|
servo3.write(pos);
|
|
delay(20);
|
|
}
|
|
|
|
for (pos = 0; pos <= 180; pos += 1) { // sweep from 0 degrees to 180 degrees
|
|
// in steps of 1 degree
|
|
servo4.write(pos);
|
|
delay(20); // waits 20ms for the servo to reach the position
|
|
}
|
|
for (pos = 180; pos >= 0; pos -= 1) { // sweep from 180 degrees to 0 degrees
|
|
servo4.write(pos);
|
|
delay(20);
|
|
}
|
|
}
|
|
|